Browse all practice questions for the CFD Basic Apparatus and Hydraulics Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

CFD Basic Apparatus and Hydraulics Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • The pressure created by a column of water due to elevation is known as ______.
  • What is the purpose of the PTO in a hydraulic stabilization system?
  • What kind of actuator is specified for CFD apparatus valves?
  • Which practice supports line discipline during high-flow discharge operations?
  • 2 common types of pressure control device are pressure relief valve and _______?
  • Master intake gauge may also be referred as the vacuum or _______?
  • What is the term for the backward force experienced by firefighters when water exits a nozzle?
  • How do kinks and bends affect pressure along a hose lay?
  • Which instrument is commonly used to verify hydrant performance during a test flow?
  • What does the acronym EPU represent in power systems?
  • What verification method is specified for booster tank and vent opening readings?
  • Total Dynamic Head (TDH) is the sum of which components?
  • ______ requires each fire pump to be equipped with a pressure control valve?
  • Which axis alignment improves stability of the aerial device?
  • CFD pump foam should be used at what percent concentration for all flammable liquids fires?
  • Which term describes the pressure remaining after friction and gravity have been accounted for in the network?
  • What action is prohibited on the side of the aerial that is short jacked?
  • NFPA 1901 requires each fire pump to be equipped with which device?
  • What best describes a static water supply and its effect on firefighting operations?
  • Which two types of centrifugal pumps are described?
  • Why is a gasket seal important at hose and appliance connections?
  • In a hydraulic context, a series configuration is associated with which parameter?
  • How can you verify that a hydrant is delivering the expected flow?
  • Stability of the aerial device can be improved by operating the aerial device in line with the truck's ____________.
  • What is the purpose of a deck gun control valve?
  • How does elevation affect discharge pressure?
  • Which statement best describes the function of a bleeder valve?
  • The device that prevents backflow into the public water supply is called what?
  • Which are signs of a pump executing improperly and how would you troubleshoot?
  • Which of the following best describes the PTO’s role in hydraulic control?
  • How is priming performed when drafting from a static source?
  • Which of the following sets includes the three major discharge appliances commonly found on a pumper?
  • For a given GPM, choosing a larger-diameter hose will have what effect on friction loss per 100 ft?
  • In firefighting hydraulics, how do attack lines differ from supply lines?
  • Which factor does not influence friction loss?
  • Complete the sentence: ______ operate the aerial on the side that is short jacked.
  • When a pump is supplying multiple attack lines, any sudden flow change in one line will cause a pressure surge or drop in the others. This is called a?
  • What component is used to relieve pressure after the discharge valve has been closed?
  • All CFD pumps are which type of pump?
  • The online form must be completed during which time window?
  • Which statement about Total Dynamic Head (TDH) is true?
  • What is the role of the discharge line when drafting from a hydrant?
  • Which statement is true about nozzle pressures for smooth bore vs fog nozzles?
  • Stored potential energy for forcing water thru pipe, fittings, fire hose and adaptors is known as ______.
  • Rotary pump has two subtypes: rotary gear and which?
  • What is hydrostatic testing used for?
  • When checking or adjusting a relief valve, which guideline is correct?
  • Pressure found in water distribution system during normal consumption demands is known as ______.
  • Removing all water from the fire pump when apparatus is stored in ________?
  • The passage area of the pump casing that increases in size as it gets closer to the discharge is known as what?
  • That part of the total available pressure not used to overcome friction or gravity while forcing water thru pipe, fittings, adaptors, and fire hose is known as ______.
  • A _______ is used to relieve pressure after the discharge valve has been closed?
  • What is a smooth bore nozzle and when is it typically used?
  • Which device is used to monitor and compare engine intake pressures on a fire pump system?
  • If the friction loss per 100 ft for 1.75 inch hose at 150 GPM is 15 psi, what is total friction loss for 300 ft?
  • EPU stands for
  • The aerial device should extend _____ feet beyond the roof's edge to allow safe entry, exit, and so it is easily spotted by firefighters on the roof.
  • During high-rise operations, what discharge pressure should the operator maintain?
  • The ___________ is measured from the highest rung at full elevation & extension to the ground.
  • In centrifugal pump terminology, what is the term for the central region where fluid enters the impeller?
  • Which action is prohibited when the aerial is on the short-jacked side?
  • What checks should be performed before starting a pump?
  • What safety considerations are essential during high-flow discharge operations?
  • Which standard governs the fire apparatus driver/operator professional qualification?
  • Engines companies should __________?
  • Which term describes the pressure in a water distribution system during typical demand?
  • Positive Displacement Pumps have two main types of pumps: Piston pump and which?
  • Which factor is directly linked to the speed of the impeller?
  • Positive Displacement Pumps have two main subtypes; one is Piston pump. What is the other subtype?
  • If the side of the aerial is short jacked, you should
  • Which rpm range corresponds to the typical impeller operation?
  • Which option best describes the relationship between a ball valve and flow resistance?
  • What is a likely consequence of omitting a gasket at a hose or appliance connection?
  • Which two devices are the two common types of pressure control devices?
  • How should booster tank and vent openings levels be checked?
  • What two metrics are typically indicated in hydrant test data?
  • Which statement is true about EPU in power systems?
  • If a deck gun flow is not as expected, what checks would you perform?
  • How should you check or adjust a relief valve on a pumper?
  • What information is used to evaluate hydrant flow availability?
  • The discharge pressure of a centrifugal pump is influenced by the speed of the impeller.
  • Nozzle pressure values and typical nozzle pressures?
  • What is the purpose of intake and discharge pressure gauges on a pumper?
  • ALWAYS MAINTAIN A DISTANCE OF AT LEAST __ FEET BETWEEN THE AERIAL DEVICE AND ELECTRICAL LINES.
  • What is the required time window for pressure control valve to operate after a rise in pressure, per NFPA 1901?
  • What is residual pressure in a firefighting hydraulic system?
  • Effective apparatus operation ______ with the proper placement of apparatus at an incident.
  • During hydrant testing, which step helps confirm the system is delivering design flow?
  • What is water hammer and how can it be prevented during pumping operations?
  • Which term describes the pressure caused by the elevation of a water column?
  • For high rise operation the driver/operator should pump and maintain a discharge pressure of
  • Centrifugal pumps are valued for flexibility and which other attribute?
  • If discharge pressure is lower than expected with full throttle, what steps should you take?
  • When troubleshooting a pump executing improperly, which checks are recommended?
  • Which condition prompts removing all water from a fire pump before storage?
  • PSI stands for?
  • In high-flow discharge operations, what does line discipline refer to?
  • How do you estimate friction loss using hose charts?
  • If you double hose length from 100 ft to 200 ft, what happens to total friction loss?
  • How does hose diameter affect friction loss at a given flow?
  • When flushing the system, you should flush until what condition is met?
  • Class 1 systems are designed for which group?
  • The operation of a centrifugal pump is based on the principle that water introduced at the center is thrown toward the outer edge from which part at the center?
  • Which method can be used to verify hydrant flow?
  • Which of the following is NOT one of the three main factors that influence a centrifugal fire pump's discharge pressure?
  • A standpipe with a height of 100 feet, containing water, would have a base pressure of ?
  • Should functional tests be performed inside the station?
  • What is relay pumping?
  • What is priming and why is it necessary for suction operations?
  • Centrifugal pumps are classified as which type of pump?
  • The device abbreviated as EPU is typically used to provide
  • If the pump is cavitating, what is a likely cause?
  • Which statement is true regarding the side of the aerial that is short jacked?
  • How would you estimate friction loss for 200 ft of 1.75-inch hose delivering 150 GPM?
  • What is a relief valve on a pump and why is it used?
  • If you suspect a leak in the discharge system during testing, what is the appropriate action?
  • Which factor is not included in the Total Dynamic Head (TDH)?
  • The volute in a pump serves to do what to the cross-sectional area along the flow path?
  • What is static pressure in a firefighting hydraulic system?
  • The system that provides power to a hydraulic pump to control stabilizers by directing hydraulic fluid through valves is the
  • What term describes the amount of water a system can deliver per unit time, often referred to as volume in pump discussions?
  • 2 common types of pressure control device are pressure governor and _______?
  • D/O should not allow residual pressure to fall below _____ on the master intake gauge
  • Friction loss per 100 ft is used in calculations to estimate total friction loss by multiplying by hose length in hundreds of feet.
  • Which sequence correctly describes typical steps to prime a pump?
  • The forward pressure of a stream of water as it leaves an orifice (nozzle) is called ______.
  • What is the difference between a master stream and an attack line in terms of flow and purpose?
  • Which statement about relief valve operation is correct?
  • Which statement best describes CFD pumps based on the given material?
  • Which term describes the distance from the ground to the highest reach of the aerial device?
  • Why are check valves used in the discharge system?
  • Friction loss in a firefighting hydraulic system is the pressure drop caused by water flowing through hoses and pipes. It is influenced by which factors?
  • Rotary pump has two types of pumps: Rotary gear and which?
  • Which SOG specifies that an appropriate online form should be completed during the first hour of the shift?
  • Which statement about friction loss charts is true?
  • The most common priming inhibitor in drafting operations is an ______.
  • At the same GPM, which statement about nozzle pressures is true?
  • How does suction lift influence pump performance?
  • Two widely used pump types in the fire service include Positive Displacement Pump and which other pump?
  • In the hydraulic stabilization system, controlling stabilizers is achieved by directing fluid through valves using which system?
  • The aerial device is least stable when oriented perpendicular to the truck's longitudinal axis. Which description best matches this orientation?
  • Head pressure in hydraulic calculations is expressed by multiplying vertical difference in feet by which constant?
  • Should the discharge supply to a sprinkler system be shut down without instruction from the Incident Commander?
  • According to NIOSH, what percentage of firefighter fatalities occur while responding to or returning from a call?
  • What device consists of one-way check valves and is designed to keep water or contaminants from re-entering the public water supply?
  • The most common type of valve is a _________?
  • How do you handle a failing pump primer?
  • Which term describes the energy stored to push water through pipes and hoses?
  • What is the maximum allowed increase above the valve set pressure, as specified by NFPA 1901?
  • Abbreviation of inches of mercury?
  • What safety devices protect a pump and its discharge lines from overpressure?
  • How can you verify that a hydrant can deliver the design flow?
  • The aerial apparatus is least stable when the aerial device is operated __________- to the longitudinal axis of the truck.
  • In a series arrangement of components, which parameter is primarily increased?
  • Which standard governs the equipment requirements for fire pumps as described in the material?
  • If no water is being used for an extended time and the line must remain under pressure, the pump will ______?
  • Which routine maintenance task should be performed on pumping equipment?
  • In horizontal ventilation, to avoid venting heat and smoke, where should the vent be placed relative to the window?
  • Which item completes the list of three main factors that influence a centrifugal fire pump's discharge pressure?
  • Sprinkler / Standpipe systems should be supplied by using 3 inches or ___ hose.
  • NFPA 1901 requires that a pressure control valve to operate within ______ following a rise in pressure and permits no more than a _____ increase above it set pressure?
  • Which factors influence nozzle selection for an attack line?
  • Extending the aerial device beyond the roof edge serves which purpose?
  • Select the correct expansion for the acronym EPU.
  • Two widely used pump types in the fire service include Centrifugal Pump and which other pump?
  • The pump impeller generates RPM within which range?
  • During high-rise operations, who is responsible for pumping and maintaining the discharge pressure?
  • Class 3 fire protection systems are designed for which groups?
  • Master intake gauge may also be referred as compound or _______?
  • In horizontal ventilation the tip should be placed on the ______ side and slightly ______ the window. This allows firefighters to vent a window without encountering heat, smoke, and falling glass.
  • What is the purpose of hydrant connections, and their typical operation?
  • Class 2 systems are designed for which group?
  • How should you perform a basic discharge valve check during an incident?
  • Ball valve permits a full flow through the lines with a minimum of ___________?
  • Volume can also be called which term?
  • The best victim rescue approach is always made on the ______ side of the fire if possible, however, the aerial tip should be placed directly at or just below the ________.
  • Head pressure is calculated by multiplying the total vertical difference in feet by which constant?
  • If hydrant flow is lower than expected, what is an appropriate action?
  • What safety considerations are necessary when drafting near traffic or obstacles?
  • The forward pressure of a water stream leaving a nozzle is referred to as what?
  • Cavitation is a condition where water is being discharged faster than it is entering the pump.
  • Centrifugal pumps are classified as which type of pump?
  • What happens if a pump is not primed when drawing from a static source?
  • What is the most common pump mount?
  • What is a Siamese appliance and what is its purpose?
  • During operation, which gauge reading verifies nozzle pressure and overall system performance?
  • Why should suction lift be minimized during drafting?
  • Which safety practices are important during high-flow discharge operations?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy